Laptop Troubleshooting and Repair in hyderabad call@ 8885420929
- Toshiba, Dell, HP, Thinkpad, Acer and Sony laptops
The first step in repairing any laptop or notebook is troubleshooting the problem accurately. For example, some people will run out and buy a new battery on the assumption it's failed when the problem is a frayed wire or a bad connector on the power cord, something that can be fixed with a little solder or electric tape. Likewise, a "dead" LCD screen could be a mainboard or video adapter failure, a bad inverter or a burnt out backlight. When the LCD itself needs replacing, it will probably be due to a physical crack in the glass or blocks of dead pixels. If your CD or DVD drive won't work anymore, make sure you've tried a selection of discs and try a cleaner kit before replacing the drive, and always double-check the connection before discarding the old drive. About the only problems that will identify themselves as imminent failures are increasingly loud hard drives or steadily decreasing battery life over time. The troubleshooting flowcharts below are linked to the full size troubleshooting flowcharts and text excerpted from "The Laptop Repair Workbook "
Ports and Power Connector
Laptops are sometimes plagued by internal failure of the physical connectors, like the modem or network port seems to be detached within the case, making it tough to get a good connection, or the power connector solder joint to the board breaks. The only way to fix these problems is to open up the body of the laptop, determine exactly what has broken, and do your best to restore it to the original condition, rather than just kludging it. The problem with kludging anything in a notebook is that the tolerances are so tight that your kludge might fail as soon as you snap the case back together. When soldering anything on a laptop board, use a fine tip iron and don't gamble on overheating the board and stripping away circuitry. Use a decent solder sucker to quickly clean up the old solder rather than fooling around with copper wick, and if you get the feeling you're taking to long, just stop and let it all cool down before trying again.
Power Failure
If your laptop doesn't turn on when you hit the power button, the power system is a logical place to begin the troubleshooting process. The laptop power system can be viewed as three separate parts: The A/C adapter that gets plugged into a power outlet on one end and into the laptop on the other end, the laptop motherboard or power regulation daughter card that monitors and distributes power to the laptop components, and the battery. The vast majority of laptops manufactured these days can operate without the battery installed. In some cases, the manufacturers will suggest that you remove the battery and store it somewhere cool if using the laptop in one location for extended periods of time, as in weeks or months.
One of the oddities about troubleshooting laptop power failure as opposed to PC power failure is that the battery gives the laptop an independent power system for as long as the charge lasts. If the PC in your home is plugged into a bad power outlet or its power strip is accidentally switched off you'll quickly figure out why. But if the power strip gets turned off while you are operating your laptop, or a breaker trips, or the local power grid suffers a brown out, you might not even notice until the battery runs down. That's why it's important to not jump to conclusions about laptop battery failures, and to try charging the battery under different conditions before giving up and buying a new one. Just because the battery didn't charge while the laptop was plugged in doesn't mean the battery is bad.
It pays to go online and read the owners manual for extending the life of the battery in your particular laptop model if you didn't do so when you obtained it. Some older notebooks require that you cycle the battery continually, only working on AC power for as long as it takes to recharge the exhausted battery. Many newer models want you to fully discharge the battery around once a week, but otherwise don't care about leaving it plugged in the rest of the time, and newest designs don't care what you do as long as the laptop actually gets run on battery for a reasonable percentage of the time. If you think your battery is running down too fast, make sure you have enabled the aggressive power saving modes in software (usually accessed through Control Panel or the manufacturers icon) which dim the screen, slow the CPU, and let the hard drive spin down when unused. Also, keep in mind that the level of estimated battery life remaining that causes an onscreen alarm can be set by the user, and if your default setting is very conservative (between 10% and 20%), you may want to experiment with a lower level (between 3% and 5%) that will still give you time to save your work and shut down before the laptop goes into hibernation.
If the external monitor works fine, your failure is with the laptops video subsystem, which is usually contained entirely in the screen/lid assembly. There is a decent chance that one of the cable bundles (video signal or power) that run through the hinges to the video subsystem has failed, so unless the failure is obvious (cracked screen, fading in a corner, faint image, bad pixels), you should still open up the main body of the laptop as well to visually inspect the connections. The easiest problem to identify is obviously a cracked LCD, but a slowly increasing number of dead spots or whole rows or columns on the screen indicates the the actual LCD assembly is bad. Replacing the LCD is pretty much the same on most notebooks, Dell has a nice backlight design, the real challenge is getting the lid open and removing it without breaking anything.
Hard Drive Failure
No comments:
Post a Comment